美利体育登录入口官网

热能计数器及其组件接收检查

Acceptance inspection of heat meters and heat meter sub-assemblies

铜；铅；锌和镍精矿．散装精矿干燥失量的测定

Copper, lead, zinc and nickel concentrates - Determination of mass loss of bulk material on drying

大批量机器组装紧固件的检验和质量保证的补充

Supplement to Inspection and Quality Assurance for High Volume Machine Assembly Fasteners

高度专业化工程应用紧固件的检验和质量保证

Inspection and Quality Assurance for Fasteners for Highly Specialized Engineered Applications

标签标明的缝纫线每团长度的标准规格

Standard Specification for Labeled Length per Holder of Sewing Thread

工业化学品抽样的的标准实施规程

Standard Practice for Sampling Industrial Chemicals

测试骨料 第102部分：取样方法

Testing aggregates — Part 102 : Methods for sampling

固定的立式道路交通标志.工厂生产控制

Fixed, vertical road traffic signs — Part 4: Factory production control

可运输的气瓶.容量小于150 litres的可再充气焊接插座.用实验方法证明设计制成的焊接奥氏体不锈钢气瓶

Transportable gas cylinders - Refillable welded receptacles of a capacity not exceeding 150 litres - Welded austenitic stainless steel cylinders made to a design justified by experimental methods

锌和锌合金 铸造用合金 铸锭和熔液

Zinc and zinc alloys. Alloys for foundry purposes. Ingot and liquid

商用弹药推进剂规范 - 要求和测试方法

Specification for Propellants for commercial ammunition — Requirements and test methods

保健品灭菌 辐射 确定灭菌剂量

Sterilization of health care products. Radiation - Establishing the sterilization dose

流动谷物和磨碎的谷物产品 — 通过机械方式自动取样

Flowing cereals and milled cereal products — Automatic sampling by mechanical means

地工合成材抽样法

Mehtod of test for sampling of geosynthetics

结件之允收检验

Fasteners－Acceptance inspection

液氢气瓶 第1部分：材料、设计、制造、检验与试验

Liquid Hydrogen Cylinder Part 1: Materials, Design, Manufacturing, Inspection, and Testing

农产品质量安全监测抽样技术规范

Agricultural product quality and safety monitoring and sampling technical specifications

土壤改良剂和生长介质-颗粒尺寸大于60毫米的材料的数量测定（草案）

Soil improvers and growing media - Determination of quantity for materials with particle size greater than 60 mm

排水沟和下水道用陶瓷粘土管道系统第2部分：合格评定和取样

Vitrified clay pipe systems for drains and sewers - Part 2: Evaluation of conformity and sampling; German version EN 295-2:2013

混凝土、砂浆和灌浆用外加剂第6部分：性能稳定性的取样、评估和验证

Admixtures for concrete, mortar and grout - Part 6: Sampling, assessment and verification of the constancy of performance; German version EN 934-6:2019

不定形耐火制品 第2部分：测试取样

Monolithic (unshaped) refractory products - Part 2: Sampling for testing (ISO 1927-2:2012); German version EN ISO 1927-2:2012

聚烯烃农用线

Polyolefin agricultural twines (ISO 4167:2006); German version EN ISO 4167:2006

气瓶.可重复充装的无缝钢气瓶.设计、结构和试验.第2部分:抗拉强度大于或等于1100 MPa的淬火加回火钢瓶(ISO 9809-2-2010).德文版本EN ISO 9809-2-2010

Gas cylinders - Refillable seamless steel gas cylinders - Design, construction and testing - Part 2: Quenched and tempered steel cylinders with tensile strength greater than or equal to 1100 MPa (ISO 9809-2:2010); German version EN ISO 9809-2:2010

烟花爆竹 抽样检查规则

Fireworks and firecrackers sampling inspection rules

军工产品批次管理的质量控制要求

Quality control requirements for batch management of military products

帘布.验收规程和取样方法

Cord fabric. Rules of acceptance and sampling method

纤维素.批的商品量的测定.第1部分.成捆包装的片状纤维素

Pulps. Determination of saleable mass in lots. Pulp baled in sheet form

架空输配电线路硬件测试的 IEEE 标准

IEEE Standard for the Testing of Overhead Transmission and Distribution Line Hardware

细切烟草及其烟制品 取样、调节和分析方法 第1部分：取样

Fine-cut tobacco and smoking articles made from it - Methods of sampling, conditioning and analysis - Part 1: Sampling

天然橡胶乳胶男性避孕套 - 要求和测试方法

Natural rubber latex male condoms — Requirements and test methods

速溶咖啡.带衬里的块装件的取样方法

Instant coffee - Sampling method for bulk units with liners

粘合剂.一般测试方法.第2部分:取样

Adhesives -- General testing methods -- Part 2: Sampling

运输用气瓶 0.5 L 及以下容积的压缩、液化和溶解气体气瓶 以及 1 L 及以下容积的二氧化碳填充用无缝标准锰钢气瓶的设计与构造技术规范...

Transportable gas cylinders - Specification for the design and construction of refillable transportable seamless normalized carbon manganese steel gas cylinders of water capacity up to 0,5 litre for compressed, liquefied and dissolved gases and up to 1...

纸张和纸板 水分含量的测定 烘箱法（ISO 287:2017）

Paper and board - Determination of moisture content of a lot - Oven-drying method (ISO 287:2017)

食品 食品中放射活性的测量 第1部分：食品食品的运输和保护指南 实验室的获得

Food products - Measurement of radioactivity in foodstuffs - Part 1: guide to the sampling, transport and storage of foodstuffs - Obtaining a laboratory sample

鞋类 检验规则及标志、包装、运输、贮存

Footwear.principle of inspection and marking, package,transportation,storage

碳素钢和低合金钢锻件的质量保证抽样与测试

Quality Assurance Sampling and Testing, Carbon and Low-Alloy Steel Forgings

润滑油,内燃机,军事作战/战术服务

Lubricating Oil@ Internal Combustion Engine@ Military Combat/Tactical Service

润滑油,内燃机,保存截断

Lubricating Oil@ Internal Combustion Engine@ Preservation Break-In

自行车用焊接钢管

Steel tubes for non-pressure purposes Part 2: Steel tubes for cycles

出口日用陶瓷抽样方法

Rules for the sampling of domesticceramics for export

进出口金属材料抽样规程

Rules for the sampling of metal material for import and export

进口可用作原料的固体废物检验检疫通用标准 第2部分：抽样方法

General Standard for Inspection and Quarantine of Imported Solid Waste as Raw Materials Part 2: Sampling Methods

进出口食品安全生物学美利体育登录入口官网抽样规范

Sampling standard for biology detection of import and export food safety

固体材料取样指南

Guide for sampling of solid materials

可运输气瓶 可再充装焊接钢气瓶 设计和构造 第1部分：碳钢

Transportable gas cylinders - Refillable welded steel gas cylinders - Design and construction - Part 1: Carbon steel

胶粘剂 取样（ISO 15605:2000）

Adhesives - Sampling (ISO 15605:2000)

化妆品 良好生产规范（GMP） 良好制造实践指南（ISO 22716:2007）

Cosmetics - Good Manufacturing Practices (GMP) - Guidelines on Good Manufacturing Practices (ISO 22716:2007)

土壤改良剂和生长介质 数量的测定

Soil improvers and growing media - Determination of a quantity