美利体育登录入口官网

新拌混凝土和易性和流变性测量报告（包含勘误表：2009年4月21日）

Report on Measurements of Workability and Rheology of Fresh Concrete (Incorporates Errata: April 21@ 2009)

预测发动机油边界泵送温度的标准试验方法

Standard Test Method for Predicting the Borderline Pumping Temperature of Engine Oil

低温下发动机机油屈服应力和表观粘度测定的标准试验方法

Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature

恒定剪切应力粘度计中传动线路润滑剂的低温粘度的标准试验方法

Standard Test Method for Low Temperature Viscosity of Drive Line Lubricants in a Constant Shear Stress Viscometer

低温下用过的发动机机油屈服应力和表观粘度测定的标准试验方法

Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature

低温下用过的发动机机油屈服应力和表观粘度测定的标准试验方法

Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature

用于测量油漆 油墨和相关液体材料屈服应力的标准测试方法

Standard Test Methods for Measurement of Yield Stress of Paints, Inks and Related Liquid Materials

D4684-测定发动机油低温屈服应力和表观粘度的试验方法

D4684-Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature

D4684-测定发动机油低温屈服应力和表观粘度的试验方法

D4684-Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature

D4684-测定发动机油低温屈服应力和表观粘度的试验方法

D4684-Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature

D4684-测定发动机油低温屈服应力和表观粘度的试验方法

D4684-Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature

涂覆织物试验.方法21.伸长和拉伸永久变形测定方法

Testing coated fabrics - Method 24 - Method for determination of elongation and tension set

便携式气体容器 - 容量为0.5升至150升的无缝铝制和铝合金可再填充运输用气瓶的设计与构造规范

Transportable gas cylinders — Specification for the design and construction of refillable transportable seamless aluminium and aluminium alloy gas cylinders of capacity from 0,5 litre up to 150 litre (includes amendment A1:2003)

储气瓶.可再充装的焊接不锈钢气瓶.试验压力≥6MPa

Gas cylinders - Refillable welded stainless steel cylinders - Test pressure greater than 6 MPa

热塑管道.拉伸性能的测定.第1部分:通用试验方法(ISO 6259-1-2015);德文和英文版本EN ISO 6259-1-2015

Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015); German and English version EN ISO 6259-1:2015

发动机油边界泵送温度测定法

Engine oil--Determination of borderline pumping temperature

气瓶.可再充装的焊接铝合金气瓶.设计、结构和试验

Gas cylinders - Refillable welded aluminium-alloy cylinders - Design, construction and testing

低温下发动机油屈服应力和表观黏度测定的试验方法

TEST METHOD FOR DETERMINATION OF YIELD STRESS AND APPARENT VISCOSITY OF ENGINE OILS AT LOW TEMPERATURE

用过发动机油低温下屈服应力和表观黏度测定法

Standard test method for determination of yield stress and apparent viscosity of used engine oils at low temperature

可运输气瓶 可再充装、可运输焊接铝合金气瓶的设计和建造规范

Transportable gas cylinders - Specification for the design and construction of refillable transportable welded aluminium alloy gas cylinders

可运输的气瓶 容量为1000升及以下的压力焊接气 drum 设计和构造 运输气体用

Transportable gas cylinders - Specification for welded pressure drums up to 1000 litre capacity for the transport of gases - Design and construction

可搬运气瓶 容积不超过150升的可充装焊接容器 第1部分：设计依据为实验方法的奥氏体不锈钢焊接气瓶

Transportable gas cylinders - Refillable welded receptacles of a capacity not exceeding 150 litres - Part 1: Welded austenitic stainless steel cylinders made to a design justified by experimental methods

气瓶 可充装焊接不锈钢气瓶 第1部分：试验压力6 MPa及以下（ISO 18172-1:2007 等同）

Gas cylinders - Refillable welded stainless steel cylinders - Part 1: Test pressure 6 MPa and below (ISO 18172-1:2007, IDT)