共找到 150 条与 eNodeB 相关的标准，共 10 页
本文件是关于LTE TDD家庭基站射频要求工作项目的技术报告，该工作项目在TSG RAN#43会议上获得批准。该工作项目的目标是首先识别相关场景，然后编写适用于LTE TDD家庭基站的射频要求规范。
LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); TDD Home eNode B (HeNB) Radio Frequency (RF) requirements analysis (3GPP TR 36.922 version 9.0.0 Release 9)
The present document is the technical report for the work item on LTE TDD HeNB RF requirements, which was approved at TSG RAN#43. The objective of the WI is to first identify the relevant scenarios and then write an RF requirements specification that is applicable to LTE TDD HeNB.
LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); TDD Home eNode B (HeNB) Radio Frequency (RF) requirements analysis (3GPP TR 36.922 version 15.0.0 Release 15)
This document is a technical report of the work item on FDD Home eNodeB RF Requirements [1]. The goal of this technical report is to satisfy the two objectives of the work item, which are reproduced below, Objective 1 The existing E-UTRA BS class does not fully address the RF requirements of the HeNB application. Correspondingly, Objective 1 is to specify the RF requirements for the Home eNodeB in TS 36.104, where the work done for the HNB can be taken as a basis. Furthermore, the test specification TS 36.141 would need to be updated accordingly. It is foreseen that the HeNB-specific additions to TS 36.104 / 36.141 can be accommodated in a manner similar to that accomplished for the UTRA HNB. Objective 2 TR 25.820 showed that for the CSG HNB there are occasions where overall system performance may be enhanced by controlling the HNB output power dependent on the strength of signal from the macro cell layer and from other HNB. Control of CSG HNB output power mitigates interference to the macro layer and other CSG HNB. Correspondingly, it is expected that similar observations may be made for the HeNB. Objective 2 is to ensure that operators have the ability to achieve control of HeNB power; in particular, the work should cover but not be limited by the following, ? The operator has the means to obtain measurements of the strength of signals and the identity (to allow macro neighbour cell list building) from the macro cell layer and from other HeNBs. Measurements may be made by the HeNB or may make use of existing measurements defined for the UE; no new UE measurements will be defined. ? The operator has the means to set the maximum output power of the HeNB, this is expected to introduce changes to TS 36.104. ? The operator has guidance on how to control HeNB power and expected performance levels in the relevant scenarios. There are additional factors that may be controlled in E-UTRA in comparison with UTRA, such as variable bandwidth and allocation of radio sub-carriers; work will be conducted to investigate if similar mechanisms may be used for controlling HeNB resource allocation versus the macro cell layer and versus other HeNBs. Additionally, mechanisms may be applied to control HeNB coverage in the case of open access HeNB. As objective 2 of the work item is to create a published document to provide guidance to operators it is necessary to issue a TR in the 900 series. To avoid administrative overhead this TR will also be used to document any other output from this work item.
LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); FDD Home eNode B (HeNB) Radio Frequency (RF) requirements analysis (3GPP TR 36.921 version 15.0.1 Release 15)
本文件是FDD家庭增强型Node B（HeNB）射频要求工作项目的技术报告。本技术报告的目标是满足工作项目的两个目标： 目标1：现有的E-UTRA基站类别未完全解决HeNB应用的射频要求。因此，目标1是在TS 36.104中指定家庭增强型Node B的射频要求，其中HNB的工作可作为基础。此外，测试规范TS 36.141也将相应更新。预计TS 36.104/36.141中针对HeNB的补充内容可以以类似于UTRA HNB完成的方式容纳。 目标2：TR 25.820表明，对于CSG家庭Node B，在某些情况下，根据宏层和其他家庭Node B的信号强度控制HNB的输出功率可以提高整体系统性能。控制CSG HNB输出功率可减轻对宏层和其他CSG HNB的干扰。因此，预计HeNB也可能有类似的观察结果。目标2是确保运营商有能力控制HeNB功率；特别是，工作应涵盖但不限于以下内容： ? 运营商拥有获取宏层和其他HeNB的信号强度及身份（用于构建宏邻区列表）的测量手段。测量可由HeNB进行，也可利用为UE定义的现有测量；不定义新的UE测量。 ? 运营商拥有设置HeNB最大输出功率的手段，预计这将引入对TS 36.104的更改。 ? 运营商拥有如何在相关场景中控制HeNB功率及预期性能水平的指导。与UTRA相比，E-UTRA中可能存在其他可控制的变量，如可变带宽和无线电子载波的分配；将开展工作调查是否可使用类似机制来控制HeNB资源分配与宏层及其他HeNB的关系。此外，机制也可应用于控制开放接入HeNB的覆盖范围。 由于工作项目的目标2是创建一份发布文档以向运营商提供指导，因此有必要发布900系列的技术报告（TR）。为避免行政负担，本TR也将用于记录该工作项目的任何其他输出。
LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); FDD Home eNode B (HeNB) Radio Frequency (RF) requirements analysis (3GPP TR 36.921 version 10.0.0 Release 10)
This document is a technical report of the work item on FDD Home eNodeB RF Requirements [1]. The goal of this technical report is to satisfy the two objectives of the work item, which are reproduced below, Objective 1 The existing E-UTRA BS class does not fully address the RF requirements of the HeNB application. Correspondingly, Objective 1 is to specify the RF requirements for the Home eNodeB in TS 36.104, where the work done for the HNB can be taken as a basis. Furthermore, the test specification TS 36.141 would need to be updated accordingly. It is foreseen that the HeNB-specific additions to TS 36.104 / 36.141 can be accommodated in a manner similar to that accomplished for the UTRA HNB. Objective 2 TR 25.820 showed that for the CSG HNB there are occasions where overall system performance may be enhanced by controlling the HNB output power dependent on the strength of signal from the macro cell layer and from other HNB. Control of CSG HNB output power mitigates interference to the macro layer and other CSG HNB. Correspondingly, it is expected that similar observations may be made for the HeNB. Objective 2 is to ensure that operators have the ability to achieve control of HeNB power; in particular, the work should cover but not be limited by the following, ? The operator has the means to obtain measurements of the strength of signals and the identity (to allow macro neighbour cell list building) from the macro cell layer and from other HeNBs. Measurements may be made by the HeNB or may make use of existing measurements defined for the UE; no new UE measurements will be defined. ? The operator has the means to set the maximum output power of the HeNB, this is expected to introduce changes to TS 36.104. ? The operator has guidance on how to control HeNB power and expected performance levels in the relevant scenarios. There are additional factors that may be controlled in E-UTRA in comparison with UTRA, such as variable bandwidth and allocation of radio sub-carriers; work will be conducted to investigate if similar mechanisms may be used for controlling HeNB resource allocation versus the macro cell layer and versus other HeNBs. Additionally, mechanisms may be applied to control HeNB coverage in the case of open access HeNB. As objective 2 of the work item is to create a published document to provide guidance to operators it is necessary to issue a TR in the 900 series. To avoid administrative overhead this TR will also be used to document any other output from this work item.
LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); FDD Home eNode B (HeNB) Radio Frequency (RF) requirements analysis (3GPP TR 36.921 version 18.0.0 Release 18)
本文件是关于FDD家庭eNodeB射频要求工作项目的技术报告[1]。该技术报告的目标是满足工作项目的两个目标，具体如下： 目标1 现有的E-UTRA基站类别并未完全解决家庭eNodeB（HeNB）应用的射频要求。因此，目标1是在TS 36.104中规定家庭eNodeB的射频要求，其中可以参考为HNB所做的工作。 此外，测试规范TS 36.141也需要相应更新。 预计TS 36.104 / 36.141中关于HeNB的特定补充可以以类似于UTRA HNB的方式完成。 目标2 TR 25.820表明，对于CSG HNB，在某些情况下，通过根据宏蜂窝层和其他HNB的信号强度控制HNB输出功率，可以提高整体系统性能。控制CSG HNB的输出功率可以减轻对宏层和其他CSG HNB的干扰。相应地，预计对于HeNB也会有类似的观察结果。目标2是确保运营商有能力控制HeNB的功率；特别是，工作应包括但不限于以下内容： ? 运营商有手段获取来自宏蜂窝层和其他HeNB的信号强度测量和身份（以允许构建宏邻区列表）。测量可以由HeNB进行，也可以利用为UE定义的现有测量；不会定义新的UE测量。 ? 运营商有手段设置HeNB的最大输出功率，预计这将引入对TS 36.104的更改。 ? 运营商有关于如何控制HeNB功率的指导以及在相关场景中的预期性能水平。与UTRA相比，E-UTRA中可能有更多因素可以控制，例如可变带宽和无线子载波的分配；将进行研究以调查是否可以使用类似的机制来控制HeNB资源分配相对于宏蜂窝层和其他HeNB。此外，可以应用机制来控制开放访问HeNB的覆盖范围。 由于工作项目的目标2是创建一个发布文件以向运营商提供指导，因此有必要发布900系列的技术报告。为了避免管理开销，本技术报告也将用于记录本工作项目的其他输出。
LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); FDD Home eNode B (HeNB) Radio Frequency (RF) requirements analysis (3GPP TR 36.921 version 16.0.0 Release 16)
本文档是关于FDD家庭式eNodeB（HeNB）射频（RF）需求的技术报告工作项目。本报告的目标是满足该工作项目的两个目标： 目标1：现有的E-UTRA基站类别未能完全解决HeNB应用的射频需求。因此，目标1是在TS 36.104中指定家庭式eNodeB的射频需求，其中可以利用为HNB所做的工作作为基础。此外，测试规范TS 36.141也将需要相应更新。预计TS 36.104/36.141中针对HeNB的补充内容可以以类似于UTRA HNB完成的方式来容纳。 目标2：TR 25.820表明，对于CSG HNB，在某些情况下，根据宏小区层和其他HNB的信号强度控制HNB输出功率可能会增强整体系统性能。控制CSG HNB的功耗可以减轻对宏层和其他CSG HNB的干扰。相应地，预计类似的观察结果可能适用于HeNB。目标2是确保运营商有能力控制HeNB功率；特别是，工作应涵盖但不限于以下内容：运营商应拥有获取宏小区层和其他HeNB的信号强度及身份（用于构建宏小区邻区列表）的测量手段。测量可由HeNB进行，也可利用UE中已定义的测量；不定义新的UE测量。运营商应拥有设置HeNB最大输出功率的手段，这预计将对TS 36.104进行更改。运营商应有关于如何在相关场景中控制HeNB功率的指导以及预期性能水平。与UTRA相比，E-UTRA中可能存在其他可控因素，如可变带宽和无线电子载波的分配；将开展工作调查是否可使用类似机制来控制HeNB相对于宏小区层和其他HeNB的资源分配。此外，对于开放接入HeNB的情况，可能应用机制来控制HeNB覆盖范围。
LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); FDD Home eNode B (HeNB) Radio Frequency (RF) requirements analysis (3GPP TR 36.921 version 11.0.0 Release 11)
本文件是关于LTE TDD HeNB射频要求的技术报告，该工作项目在TSG RAN#43会议上获得批准。该工作项目的目标是首先确定相关场景，然后编写适用于LTE TDD HeNB的射频要求规范。
LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); TDD Home eNode B (HeNB) Radio Frequency (RF) requirements analysis (3GPP TR 36.922 version 18.0.0 Release 18)
Universal Mobile Telecommunications System (UMTS); LTE; Telecommunication management; Self-Organizing Networks (SON); Self-establishment of eNodeBs; Concepts and requirements (V8.0.0; 3GPP TS 32.501 version 8.0.0 Release 8)
本文件描述了自配置的工作原理概念以及支持此功能需要满足的IRP要求。文件还记录了要求是通过Itf-N接口还是通过其他协议满足。本版本TS仅限于eNB的自配置。本文档中的要求不适用于HNB。
Universal Mobile Telecommunications System (UMTS); LTE; Telecommunication management; Self-Organizing Networks (SON); Self-establishment of eNodeBs; Concepts and requirements (3GPP TS 32.501 version 8.0.0 Release 8)
本文件定义了自配置IRP（SCIRP）的信息服务（IS）部分。它描述了通过Itf-N可见的信息语义和交互，以协议独立的方式进行。信息通过信息对象类（IOCs）指定，交互通过操作和通知指定。本文件未指定信息的语法（编码）。本版本TS的范围限于eNBs的自配置。本文件还描述了在自配置上下文中如何使用已定义的Itf-N功能。
Universal Mobile Telecommunications System (UMTS); LTE; Telecommunication management; Self-Organizing Networks (SON); Self-establishment of eNodeBs; Stage 2 (3GPP TS 32.502 version 8.0.0 Release 8)
本标准规定了LTE FDD数字蜂窝移动通信网第一阶段基站美利体育官网首页网址的功能、操作维护、无线指标等方面的测试方法和测试过程。 本标准适用于LTE FDD数字蜂窝移动通信网第一阶段的宏覆盖基站美利体育官网首页网址、中等覆盖和本地覆盖基站美利体育官网首页网址。
LTEFDD digital cellular mobile telecommunication network.Testmethod of eNodeB equipment (Phase 1)
本文件描述了OAM系统内自组织网络（SON）功能的要求和架构。SON包括：在OAM系统中提供SON基础设施；启用SON操作；在OAM基础设施内提供SON能力（每个能力可以是分布式或集中式），包括其管理；访问SON相关的eNodeB属性；识别SON相关的eNodeB和UE测量；访问和传输SON相关的eNodeB和UE测量；传输SON相关的eNodeB告警；定义必要的接口IRP；E-UTRAN内和不同3GPP无线接入技术之间的邻区关系列表自动化；网络中新建eNodeB的自建立；eNodeB的自配置和自愈；自动化覆盖和容量优化；由于故障排除的参数优化；由于网络中动态变化的持续优化；自动化切换优化；QoS相关无线参数的优化。SON概念和架构在第4条中描述。SON的高层要求在第5条中定义。SON的用例在第5条中描述。
Universal Mobile Telecommunications System (UMTS); LTE; Telecommunication management; Self-Organizing Networks (SON); Concepts and requirements (3GPP TS 32.500 version 9.0.0 Release 9)
本标准规定了基于LTE技术的宽带集群通信(B-TrunC)系统(第一阶段)空中接口物理层、MAC层和RRC层协议功能测试、分组数据业务测试方法。本标准适用于基于LTE技术的宽带集群通信(B-TrunC)系统(第一阶段)的基站、终端。
LTE-based broadband trunking communication (B-TrunC) system—Test methods for interface (Phase 1)—Air interface
本文件定义了演进3GPP分组交换域（在本文档中称为演进分组系统（EPS））的第2阶段服务描述。演进3GPP分组交换域使用演进通用陆地无线接入网（E-UTRAN）提供IP连接。 该规范涵盖了漫游和非漫游场景，并涵盖所有方面，包括E-UTRAN和预E-UTRAN 3GPP无线接入技术之间的移动性、策略控制和计费以及认证。 无线接入网络功能仅描述整体系统所需的部分。 TS 36.300 [5]包含演进通用陆地无线接入（E-UTRA）和演进通用陆地无线接入网络（E-UTRAN）的总体描述。 ITU-T建议I.130 [3]描述了电信服务特征的三阶段方法，ITU-T建议Q.65 [4]定义了该方法的第2阶段。 TS 23.402 [2]是本规范的配套规范。 本文档还定义了为支持蜂窝物联网（IoT）应用而优化的演进分组系统架构。 演进分组系统还支持E-UTRAN控制使用E-UTRA和另一种无线接入技术（例如NR）组合的双连接无线连接。TS 36.300 [5]包含双连接的总体描述。 TS 23.501 [83]和TS 23.502 [84]中记录了支持EPS与5GS互操作的增强功能。
LTE; General Packet Radio Service (GPRS) enhancements for Evolved Universal Terrestrial Radio Access Network (E-UTRAN) access (3GPP TS 23.401 version 17.6.0 Release 17)
