共找到 150 条与 Array 相关的标准，共 10 页
Non-destructive testing - Ultrasonic testing with arrays - Vocabulary (ISO 23243:2020)
Mechanical standardization of semiconductor devices - Part 6-13: Design guideline of open-top-type sockets for Fine-pitch Ball Grid Array and Fine-pitch Land Grid Array (FBGA/FLGA) (IEC 60191-6-13:2007)
Photovoltaische (PV) Modulgruppen aus kristallinem Silizium - Messen der Strom-/Spannungskennlinien am Einsatzort (IEC 82/693/CDV:2012); Deutsche Fassung FprEN 61829:2012
本文件规定了乳肉兼用牛Mass Array分型验证多基因聚合效应的术语与定义及主要仪器美利体育官网首页网址、主要试剂和材料、样本采集、试验步骤、试验结果、废弃物处理、安全防护、注意事项等。适用于乳肉兼用牛Mass Array分型验证多基因聚合效应。
Technical procedures for verification of multi-gene aggregation effects by Mass Array typing of dairy and meat cattle
This document specifies acceptance levels for the phased array ultrasonic testing technique (UT-PA) of full-penetration welds in low-alloy and/or fine-grained steels in the wall thickness range from 3,2 mm to 8 mm which correspond to the quality levels of ISO 5817. These acceptance levels are applicable to indications detected according to ISO 20601.
Non-destructive testing of welds - Phased array ultrasonic testing (UT-PA) for thin-walled steel components - Acceptance levels (ISO 4761:2022)
This document specifies characterization tests to be performed at the end of the fabrication of an array probe. It defines both methodology and acceptance criteria. This document is applicable to the following array probes used for ultrasonic non-destructive testing [phased array technique or signal processing technique, e.g. full-matrix capture (FMC) and total-focusing technique (TFM)] in contact technique (with or without a wedge or delay line) or in immersion technique, with centre frequencies in the range 0,5?MHz to 10?MHz: a)?????? array probes with elements in one direction: —??? 1-D-linear array (linear array); —??? 1-D-curved array; —??? annular array; b)?????? array probes with elements in two directions: —??? 2-D-array (matrix array); —??? sectorial annular array; —??? partial sectorial annular array. This document does not give methods and acceptance criteria to characterize the performance of an ultrasonic phased array instrument or the performance of a complete system, which are given in ISO?18563–1 and in ISO?18563–3.
Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 2: Array probes (ISO 18563-2:2024, IDT)
Mechanical standardization of semiconductor devices - Part 6-12: General rules for the preparation of outline drawings of surface mounted semiconductor device packages - Design guidelines for fine-pitch land grid array (FLGA)
IEC 60191-6-22:2012 provides the outline drawings and dimensions common to silicon-based package structures and materials of ball grid array packages (BGA) and land grid array packages (LGA).
Mechanical standardization of semiconductor devices - Part 6-22: General rules for the preparation of outline drawings of surface mounted semiconductor device packages - Design guide for semiconductor packages Silicon Fine-pitch Ball Grid Array and Silico
IEC 60191-6-22:2012 provides the outline drawings and dimensions common to silicon-based package structures and materials of ball grid array packages (BGA) and land grid array packages (LGA).
Mechanical standardization of semiconductor devices - Part 6-22: General rules for the preparation of outline drawings of surface mounted semiconductor device packages - Design guide for semiconductor packages Silicon Fine-pitch Ball Grid Array and Silico
Air line holders. Design and dimensions
Настоящий стандарт распространяется на матрицы пятого перехода для высадки заготовок гаек номинальным диаметром резьбы от 6 до 20 мм
Tools for cold-forming machines. 5Th station dies. Construction and dimensions
本标准适用于在实验室中使用量热计测量制冷剂和制冷剂/润滑剂混合物的质量流量。 本标准适用于制冷剂或制冷剂/润滑剂混合物的整个流束作为过冷液体进入量热计并作为过热蒸汽（蒸发器类型）离开的情况。 本标准适用于制冷剂或制冷剂/润滑剂混合物的整个流束作为过热蒸汽进入量热计并作为过冷液体（冷凝器类型）离开的情况。
Standard Methods for Refrigerant Mass Flow Measurements Using Calorimeters
本标准规定了相控阵超声美利体育登录入口官网中使用的术语和定义，涵盖声学相关术语、美利体育登录入口官网美利体育官网首页网址术语(探头和仪器)、美利体育登录入口官网技术术语以及信号和指示评估术语。
Non-destructive testing — Terminology — Terms used in ultrasonic testing with phased arrays
1???Scope This document specifies the functional characteristics of multi-channel ultrasonic phased array instruments used for array probes and provides methods for their measurement and verification. This document is also applicable to ultrasonic phased array instruments in automated systems; but other tests can be needed to ensure satisfactory performance. When the phased array instrument is a part of an automated system, the acceptance criteria can be modified by agreement between the parties involved. This document also can partly be applicable to FMC instruments and TFM instruments. This document gives the extent of the verification and defines acceptance criteria within a frequency range of 0,5?MHz to 10?MHz.
Non-destructive testing. Characterization and verification of ultrasonic phased array equipment - Instruments
本文件定义了使用阵列进行超声美利体育登录入口官网时使用的术语。这包括相控阵技术和使用阵列的信号处理技术，例如全矩阵捕获（FMC）（3.3.1.28）和全聚焦技术（TFM）（3.3.1.35）。
Non-destructive testing. Ultrasonic testing with arrays. Vocabulary
