美利体育登录入口官网

用于表面安装流体分配组件的模块化组件接口 第1部分：弹性密封件

Modular Component Interfaces for Surface-Mount Fluid Distribution Components - Part 1: Elastomeric Seals

油井弹性体测试推荐做法

Recommended Practice for Testing Oil Well Elastomers

低压应用带金属环的柔性管接头

Metal-banded flexible couplings for low-pressure applications

使用柔性弹性密封件的“玻璃纤维”（玻璃纤维增强热固性树脂）管接头的标准规范

Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals

评价可重复充装钢瓶表面涂层的试验方法

Test method for evaluating surface coatings on refillable steel cylinders

紧固夹 - 第 1 部分：带舌

Fastening clamps - Part 1: With tongue

一般用途和液压传动的连接件 带有合成橡胶或金属对金属密封的ISO 228-1螺纹端口和螺柱端 第2部分：重型 (S系列) 和轻型 (L系列) 带合成橡胶密封的螺柱端 (E型)（草案）

General purpose and hydraulic transmission connections ISO 228-1 threaded ports and stud ends with elastomer or metal-to-metal seals Part 2: Heavy-duty (S series) and light-duty (L series) Studs with elastomer seals End (Type E) (Draft)

通用和液压传动用联接件.用ISO261弹性螺纹或金属与金属密封的气门和双头螺栓端头.第2部分:(E型)带弹性密封的双头螺拴端头

Connections for general use and fluid power - Ports and studs ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 2: Stud ends with elastomeric sealing (type E) (ISO 9974-2:1996); German version EN ISO 9974-2:2000

表面安装流体分配部件用模块组成接口.第1部分:弹性密封件

Modular component interfaces for surface-mount fluid distribution components - Part 1: Elastomeric seals

通用和液压传动用联接件 带ISO 261弹性螺纹或金属-金属密封的气门和双头螺栓端头 第2部分:弹性密封的双头螺栓端头(E型)

Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 2: Stud ends with elastomeric sealing (type E)

弹性体密封件 输送气体和液态碳氢化合物管道及接头的密封件要求

Elastomeric Seals - Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids

通用和液压传动连接 与ISO 228-1螺纹和弹性体或金属对金属密封的接口和连接件端部 第2部分：重型（S系列）和轻型（L系列）连接件...

Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2022)

弹性密封技术指南

GUIDE FOR ELASTOMETRIC SEALING TECHNOLOGY

通用和流体动力连接件 带ISO 228-1弹性密封或金属对金属密封的端口和螺柱末端 第2部分：重载(S系列)和轻载(L系列)弹性密封(类型E)(ISO 1179-2:2007)

Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2: Heay-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2007)

通用和流体动力连接 带有 ISO 228-1 螺纹且带有弹性体或金属对金属密封的端口和螺柱端 第2部分：带弹性体密封的重型

Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2022)

通用和流体动力连接件 具有ISO 228-1螺纹的橡胶密封或金属对金属密封的端口和螺杆端部 第2部分：重载（S系列）和轻载（L系列）螺杆端部及橡胶密封（类型E）（ISO 1179-2:2007 等同采用）

Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2: Heay-duty (S series) and light-duty (L series) stud ends and elastomeric sealing (type E) (ISO 1179-2:2007, IDT)

液压流体动力 弹性体压缩塑料面密封件用外壳 尺寸和公差 第2部分：杆密封外壳

Hydraulic fluid power - Housings for elastomer-energized, plastic-faced seals - Dimensions and tolerances - Part 2: Rod seal housing

弹性密封件 用于给水和排水应用的管接头密封件的材料要求 4：铸造聚氨酯密封元件

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - 4: Cast polyurethane sealing elements

一般用途和流体动力连接 带 ISO 261 螺纹和弹性或金属对金属密封的端口和螺柱端 第2部分：带弹性密封的螺柱端（E 型） （ISO 9974-2:1996）

CONNECTIONS FOR GENERAL USE AND FLUID POWER - PORTS AND STUD ENDS WITH ISO 261 THREADS WITH ELASTOMERIC OR METAL-TO METAL SEALING - PART 2: STUD ENDS WITH ELASTOMERIC SEALING (TYPE E). (ISO 9974-2:1996).